georgia-market.com moderated newsgroup and market bazzar > Rome
> Construction
> Dvd set of 6 engineering milling titles
Dvd set of 6 engineering milling titles
ENGINEERING DVD'S FROM CHRONOS
Volume I Mill Basics and Clamping
In this volume, we'll discuss the basics of the mill, from terminology and basic clamping, all the way to specialized fixtures and appliances for multi-part production.
Along the way, we'll cover some of the tools and equipment you'll most likely need, and delve into how and why to make specialized fixtures.
Section 1: Introduction and Safety
Section 2: Terminolgy and Nomenclature, Tools and Equipment, Clamping Basics
Section 3: Squaring (aligning) the Stock, Squaring Round Stock, Setting up the Screwless Vise, Bedplates & Specialized Fixtures
Volume 2 Edgefinding & Location
In this volume, we'll take you into the intricacies of centering your mill spindle exactly over the edge of your workpiece, or, for that matter, anywhere else on it.
Section 1: Introduction and Safety
Section 2: The tools-edgefinder and wiggler, Using the wiggler to find an edge, Using the edgefinder to find an edge, Locating an X - Y coordinate, Finding the center of a hole or bore, Finding the center of a shaft
Section 3: Laying out your workpiece manually with temporary metal dye, Using a CAD template to lay out your workpiece, Using the wiggler's needle tool to locate layout lines and intersections
Volume 3 Precision Drilling, Reaming & Tapping
In this Volume, we'll introduce the spindle and tapers, collets and toolholders, as well as all sorts of regular and specialized drill bits, reamers and taps.
We'll drill and ream for precision press and slip fits, as well as tap accurate threads and plunge-mill flat-bottomed recesses for fastener sinking. (Counterboring.)
You'll also learn to use the telescoping gauge, along with the outside micrometer for precise bore measurements, and use a dial indicator in conjunction with a wiggler for close-tolerance work.
Section 1: Introduction, Safety and Spindle basics
Section 2: Wiggler and dial indicator for close-tolerance backlash removal, telescoping gauge and micrometer use
Section 3: Drilling, Reaming and Tapping tools, Drilling and Reaming, Tapping threads manually and plunge-milling recesses (Counterbores)
Running time: approximately 55 minutes
Volume 4 The Boring Head. Arcs, Saddles & More
This Volume will show you how to use the boring head, not only to accurately enlarge holes and cut bores for your projects, but also how to use the tool in non-centered operations, such as truing up elliptical holes and cutting arcs into flat stock, as well as cutting saddles into round stock. This little tool has a much wider range of uses than you might imagine!
Section 1: Introduction and Safety
Section 2: Standard Operations: Theory, Standard centered operations
Section 3: Non-Centered Operations: Non-centered setup, Cutting a saddle in round stock - alternate uses
Running time: approximately 45 minutes
Volume V Teardown, Tramming & Tuning
This volume will guide you step-by-step through a complete disassembly / reassembly of ALL three axes, and then will show you how to adjust the gibs to remove play and yet allow free movement of the mill bed and spindle head.
You'll also learn how to adjust the handwheel assemblies to remove unnecessary backlash, and align the X & Y axis screws to their respective nuts so as to avoid binding during travel.
Finally, you'll see the easy way to tram your mill spindle to better than .001" in all three axes.
This volume is jam-packed with easy-to-follow practical
information that is absolutely necessary if you intend to make precision parts!
Volume VI Milling, Flycutting & Dovetailing
In this volume, we'll get you started making clean and precise cuts on your workpiece.
Basic theory - Conventional vs. Climb milling
The Tools - Endmills, special cutters and nomenclature
Setting Tool Height - Different methods for setting the Z axis starting point for accurate machining
Referencing and Cutting Square - Inspecting our stock and setting it up to be cut square on all axes
Strategies for holding unsquare stock
Finishing, Deburring and Breaking Corners
Using single-point flycutters to create flawless
finishes, deburring and setting up workpieces
for close-tolerance breaking of corners and
Milling deep features - setting up and cutting
dovetails for sliding or clamping parts
Indicating the Center of a Hole or Bore
Using the test indicator to find the center of a
ALL OUR DVD'S ARE BRAND NEW BOXED ORIGINALS -
COUNTERFITTERS BEWARE - WE ALWAYS PURSUE AND PROSECUTE ANYONE SELLING FAKES!!
Be sure to add me to your favourites list!
